feat: add option to disable radio calibration and update status error handling

inc/hal_error.hpp

@@ -3,7 +3,8 @@
 #include <array>
 #include <tuple>
 
-#define APP_ERR_TBL_IT(err) {err, #err}
+#define APP_ERR_TBL_IT(err) \
+	{ err, #err }
 
 namespace app::driver::hal::error {
 using t = int;
@@ -40,7 +41,8 @@ constexpr t SPI_TIMEOUT = SPI_ERR_BASE + 2;
 constexpr t SPI_CMD_INVALID = SPI_ERR_BASE + 3;
 // The command was successfully processed, however the chip could not execute the command;
 // for instance it was unable to enter the specified device mode or send the requested data
-constexpr t SPI_CMD_FAILED = SPI_ERR_BASE + 4;
+constexpr t SPI_CMD_FAILED          = SPI_ERR_BASE + 4;
+constexpr t SPI_INVALID_RADIO_STATE = SPI_ERR_BASE + 5; /*!< Radio is in an invalid state for the requested operation */
 
 constexpr t RADIO_ERR_BASE                 = 0x1'3000;
 constexpr t RADIO_CHIP_NOT_FOUND           = RADIO_ERR_BASE + 1;
@@ -76,6 +78,7 @@ constexpr auto error_table = std::to_array<std::tuple<t, const char *>>(
 		APP_ERR_TBL_IT(SPI_TIMEOUT),
 		APP_ERR_TBL_IT(SPI_CMD_INVALID),
 		APP_ERR_TBL_IT(SPI_CMD_FAILED),
+		APP_ERR_TBL_IT(SPI_INVALID_RADIO_STATE),
 
 		APP_ERR_TBL_IT(RADIO_CHIP_NOT_FOUND),
 		APP_ERR_TBL_IT(RADIO_INVALID_TCXO_VOLTAGE),

inc/hal_spi.hpp

@@ -47,21 +47,37 @@ void init(spi_config_t config = {SPI2_HOST, 4'000'000});
 
 
 inline error_t status_to_err(const uint8_t status) {
-	const auto st = *reinterpret_cast<const llcc68::status_t *>(&status);
-	switch (st.command_status) {
-	case llcc68::CommandStatus::COMMAND_TIMEOUT:
-		return error::SPI_TIMEOUT;
-	case llcc68::CommandStatus::FAILURE_TO_EXECUTE_COMMAND:
-		return error::SPI_CMD_FAILED;
-	case llcc68::CommandStatus::COMMAND_PROCESSING_ERROR:
+	const auto st     = *reinterpret_cast<const llcc68::status_t *>(&status);
+	error_t status_ok = [](llcc68::CommandStatus st) {
+		switch (st) {
+		case llcc68::CommandStatus::COMMAND_TIMEOUT:
+			return error::SPI_TIMEOUT;
+		case llcc68::CommandStatus::FAILURE_TO_EXECUTE_COMMAND:
+			return error::SPI_CMD_FAILED;
+		case llcc68::CommandStatus::COMMAND_PROCESSING_ERROR:
 #ifdef APP_SPI_DISABLE_INVALID_STATUS_CHECK
-		return error::OK;
+			return error::OK;
 #else
-		return error::SPI_CMD_INVALID;
+			return error::SPI_CMD_INVALID;
 #endif
-	default:
-		return error::OK;
+		default:
+			return error::OK;
+		}
+	}(st.command_status);
+	if (status_ok != error::OK) {
+		return status_ok;
 	}
+	error_t chip_mode_usual = [](llcc68::ChipMode mode) {
+		switch (mode) {
+		case llcc68::ChipMode::TX:
+		case llcc68::ChipMode::RX:
+		case llcc68::ChipMode::STBY_RC:
+			return error::OK;
+		default:
+			return error::SPI_INVALID_RADIO_STATE;
+		}
+	}(st.chip_mode);
+	return chip_mode_usual;
 }
 
 /*!

inc/llcc68.hpp

@@ -494,16 +494,17 @@ inline Result<Unit, error_t> config_packet_type(uint8_t sf) {
 	res                       = set_dio_irq_params(irq_params);
 	APP_RADIO_RETURN_ERR(res);
 
+#ifndef APP_RADIO_DISABLE_CALIBRATION
 	data[0] = RADIOLIB_SX126X_CALIBRATE_ALL;
 	res     = spi::write_stream(RADIOLIB_SX126X_CMD_CALIBRATE, std::span<const uint8_t>{data, 1});
 	APP_RADIO_RETURN_ERR(res);
-
 	// The total calibration time if all blocks are calibrated is 3.5 ms. The
 	// calibration must be launched in STDBY_RC mode and the BUSY pins will be
 	// high during the calibration process. A falling edge of BUSY indicates the
 	// end of the procedure.
 	delay_ms(5);
 	while (gpio::digital_read(BUSY_PIN) == gpio::HIGH) {}
+#endif /** APP_RADIO_DISABLE_CALIBRATION */
 	return {};
 }
 
@@ -1130,19 +1131,19 @@ async_transmit(const std::span<const uint8_t> data,
 
 	Result<Unit, error_t> res;
 	res = standby();
-	APP_RADIO_RETURN_ERR_CTX(res, "failed to standby");
+	APP_RADIO_RETURN_ERR_CTX(res, "standby");
 
 	res = set_packet_params(packet_params.preamble_len, data.size(), packet_params.crc_type, packet_params.hdr_type);
-	APP_RADIO_RETURN_ERR_CTX(res, "failed to set packet params");
+	APP_RADIO_RETURN_ERR_CTX(res, "set packet params");
 
 	res = set_buffer_base_address();
-	APP_RADIO_RETURN_ERR_CTX(res, "failed to set buffer base address");
+	APP_RADIO_RETURN_ERR_CTX(res, "set buffer base address");
 
 	res = write_buffer(data);
-	APP_RADIO_RETURN_ERR_CTX(res, "failed to write buffer");
+	APP_RADIO_RETURN_ERR_CTX(res, "write buffer");
 
 	res = fix_sensitivity(mod_params.bw);
-	APP_RADIO_RETURN_ERR_CTX(res, "failed to fix sensitivity");
+	APP_RADIO_RETURN_ERR_CTX(res, "fix sensitivity");
 
 	constexpr auto irq_mask   = RADIOLIB_SX126X_IRQ_TX_DONE | RADIOLIB_SX126X_IRQ_TIMEOUT;
 	constexpr auto irq_params = irq_params_t{
@@ -1152,12 +1153,12 @@ async_transmit(const std::span<const uint8_t> data,
 		DIO3_PIN == NC_PIN ? RADIOLIB_SX126X_IRQ_NONE : irq_mask,
 	};
 	res = set_dio_irq_params(irq_params);
-	APP_RADIO_RETURN_ERR_CTX(res, "failed to set dio irq params");
+	APP_RADIO_RETURN_ERR_CTX(res, "set dio irq params");
 	clear_irq_status(irq_mask);
-	APP_RADIO_RETURN_ERR_CTX(res, "failed to clear irq status");
+	APP_RADIO_RETURN_ERR_CTX(res, "clear irq status");
 
 	res = tx();
-	APP_RADIO_RETURN_ERR_CTX(res, "failed to transmit");
+	APP_RADIO_RETURN_ERR_CTX(res, "tx");
 
 	constexpr auto TIMEOUT_FACTOR = 11u / 10u;
 	const auto timeout_us         = calc_time_on_air(data.size(),
@@ -1310,7 +1311,12 @@ static constexpr auto begin = [](const lora_parameters_t &params) -> Result<Unit
 	res = set_dio2_as_rf_switch(false);
 	APP_RADIO_RETURN_ERR_CTX(res, "set dio2 as rf switch");
 
-	res = set_frequency(params.frequency);
+#ifdef APP_RADIO_DISABLE_CALIBRATION
+	res = set_frequency(params.frequency, false);
+#else
+	res = set_frequency(params.frequency, true);
+#endif /* APP_RADIO_DISABLE_CALIBRATION */
+
 	APP_RADIO_RETURN_ERR_CTX(res, "set frequency");
 
 	// SetPacketParams

inc/llcc68_definitions.hpp

@@ -284,10 +284,12 @@ inline const char *to_str(const ChipMode &mode) {
 
 
 struct __attribute__((packed)) status_t {
+	// LSB
 	uint8_t reserved_1 : 1;
 	CommandStatus command_status : 3;
 	ChipMode chip_mode : 3;
 	uint8_t reserved_2 : 1;
+	// MSB
 };
 static_assert(sizeof(status_t) == 1);